Changing Shift Lever on 2013 Ninja 300 (EX300) (With Pictures)

Replace Ninja 300 Shift Lever

One of the architectural flaws of the 2013 ninja 300 (I haven't ridden later models, but maybe it's still the same) is that the shift lever seems to protrude out from the bike in such a way that if it even tips over, it can buckle and destroy your shift lever. I've had to replace the shift lever twice. The first time I lowsided at around 40 and the lever twisted up on itself like a pig tail (I don't have a picture of that any more unfortunately). The second time, I set the kickstand down and it happened to land right on a random bolt on the ground causing the bike to tip and fall over on the left side. Everything else was fine, but again, the shift lever got bent and unusable

It has been suggested to me to try to bend it back into place, but there are a few problems with that. First, any time you bend metal, it stresses it, making it weaker than it was before. I don't know by how much, but that's a consideration. Second, I tried to, and I couldn't get the thing to budge. I even tried heating the metal a bit but it still wouldn't go. If I had more tools and experience maybe that would be a viable option. But a new shift lever is about 40 bucks, and the tools to properly fix it are probably much more.

This is actually a pretty easy procedure, but if you've never done anything to a motorcycle before (which I hadn't the first time), it can still prove daunting to start taking pieces off your baby.

What you need:

• 1 OEM Ninja 300 Shift Lever
• This is again, assuming parts as of 2013. I don't think much has changed with this assembly in recent years, but I have to give that caveat.
• The official part number is 13242-0088. 
• You can also use the shift lever off a ninja 250. I did my first replacement with a 250 lever and it worked perfectly for 3 years (until I dropped the bike on it)
• Loctite (Blue 242)
• Breaker bar and/or torque wrench
• Note: using a torque wrench as a breaker bar is not a good idea since it's a sensitive tool. That said, with the factory Loctite on the bolt, you'll have to give it quite a bit of force to take it off.
• I just best-guessed the tightness of the bolt, but the official service manual says the torque of the bolt should be 12Nm (106 in-lb).
• Allen wrench adapter for breaker bar/torque wrench.
• Sorry, I don't know what size the bit is. Most Allen wrench bits come in a set. 
• Adjustable Wrench
• Again, sorry I don't know the specific size of the bolt. YOu don't need anything crazy here though. The nut it takes off is easy to move
• Rear Stand (OPTIONAL)
• I have a set of spools and a rear stand I use any time I'm working on my bike. It just gets it up off the ground a bit, stabilizes it, and doesn't lean towards me. However this is not necessary to do this procedure. Just a nicety.

Getting Started

I think I may have gone into more detail than is necessary for this, but my goal was to eliminate just about any ambiguity there could bein the procedure. The overview of the process is:

1. Remove shift lever bolt
2. Loosen nut on connector rod, and by hand, unscrew shift lever from rod
3. Screw the new shift lever onto the rod, and tighten the nut
4. Thread the shift lever bolt through the head of the new shift lever
5. Add a little Loctite to the bolt, make sure the shift lever is oriented correctly, and screw the lever and bolt back on to the bike (tighten to 12Nm of torque if you have a torque wrench)

Detailed Instructions

1. With your Allen bit adapter in your socket wrench, start undoing the shift lever bolt. You'll need to give it some good torque to break the Loctite, but once it gets going it should be pretty easy. As it comes out, you'll see washers on both sides. Don't lose these

   

   You'll need to give this some muscle

2. When you've entirely undone the shift lever bolt, you'll be left with your broken lever dangling from a little bar. This bar directly connects to the mechanism which makes your bike shift gears. It's an interesting little bit of engineering which you can play around with if you want. However, as I discovered on my first shift lever change, you don't need to touch anything but the one nut on the side closest to where the rod connects to the shift lever.

   

   Shift lever right after it comes
   off the bolt assembly

   
   

   

   Just hanging out...



Here's the bike-side of the bolt assembly.
I just blew some compressed air
in there and a quick rub from a rag to
clean it up

3. With the shift lever bolt detached from the bike, you now need to remove the broken shift lever from the rod. Locate the nut on the rod right up next to the shift lever. The goal here is not to remove it, but to loosen it a bit so its easier to unscrew the shift lever from the rod.

   

   In this picture, I've already loosened
   the nut on the rod a bit, so it's
   not pushing against the shift lever.

4. Now just use your hands and unscrew the shift lever from the rod. Here's a bunch of pictures of the lever as it's removed, and the bolt disassembled.
   
   
   
   

   

   Right after removal from the rod

   
   

   

   New lever (left) compared to bent lever (right)

   
   

   

   Bent lever with the bolt still in

   
   

   

   Bent lever with the bolt removed

   
   

   

   New lever with the bolt I removed
   from the bent lever in it.

   
   

   

   Another view of the new lever
   with the bolt in

5. Now we basically do everything in reverse. Use your hand and screw the new lever on to the end of the rod where the old lever was just taken off. 

   

   Lever attached to rod before
   tightening nut

   
   

   

   Lever attached to run after tightening

6. Thread the bolt through the head of the new shift lever, making sure to include the washers on both sides (you didn't lose them, did you?). Add a little bit of blue Loctite to the business end of the shift lever bolt. Orient the shift lever correctly, and loosely screw the bolt back on to the motorcycle. This can be a little confusing because the combination of the rod, the joints, and the ways you can orient everything in 3 dimensions means you can move this thing all around, and you might have even forgotten to which way to orient things to get it back on the bike. However I show the correct orientation below so if you get stuck, you should be able to emulate that. With the new lever on the rod, tighten the nut down  again. I ended up taking the bolt out temporarily while I reoriented the lever so don't be confused by the pictures with it missing. You can thread the bolt through the head it at just about any time up till you put Loctite on it.

7. 

   Threading the bolt back through
   the head of the shift lever (see
   the washer on the ground?)

   

   This is BACKWARDS! If you end up
   like this, don't worry. Just fiddle with
   all the ways you can orient the lever
   and rod until it's correct. In other words,
   so the foot-pad of the lever is pointing out 

   

   This confusing angle just shows
   how many directions this assembly
   can move it. This is me moving it
   from what you saw above (with
   the foot-pad pointing in) to the
   correct orientation (pointing out)

   

   Correct orientation 

   

   Add Loctite. A little goes a long way

   
   

   

    
   
   
8. Finally, if you have a torque wrench, tighten the bolt to the specified torque (12Nm). Otherwise, I just sort of felt it out. Tight but not too tight, ya know? 

   

   Showing how the shift lever should
   be oriented when you start tightening it

   

   Use a torque wrench if you have it

   
   

   

   Finished product!

Hope you enjoyed this!

Wildstar

Poor Wildstar. A delicious MMO undercut by some bad luck and doomed to be released in the same century as World of Warcraft. I recently started playing it again, hopeful that somehow me, little old me, by sheer willpower alone could help revitalize the community. I started leveling a character again, and in light of never being able to get into a dungeon queue, I logged on to my Warrior (or whatever the hell the big sword wielding smashy class is) who, before quitting years ago, had a burgeoning tank set. I queued for an instance and it popped. The other 4 members of the group started running off somewhere they clearly already knew, and I followed suit, while adding "Hey guys, I haven't played in quite some time, so let me know what I need to be doing). At the time, and don't ask me how, I didn't have a pair of gloves, but other than that, had mostly epics, and gear specific to tanking. But despite me assuring them that I wasn't a noob, and that I'd do just fine without a pair of gloves, they did nothing but bitch and moan about my gear, and refused to just point me in the right direction and help. And now, I know the game is doomed. It would be one thing if it were going through a rough patch, but this sentiment was not unique among this group. If you have tons of people queueing for instances, you can become accustomed to having things be just so. But in a game where there are already few players queueing for random groups, it does no good to push players away. It won't magically cause more skilled players to just show up out of the blue, and it won't encourage players to gear up, learn instances, and want to engage THEIR friends in the game. This has nothing to do with the company that makes Wildstar, but more a self defeating attitude of its players. Refusing to change their attitudes and work to better the community rather than simply complaining as the titanic goes down.